Let's Talk
+44 (0) 121 511 0400
ipu@ipu.co.uk
IPU Group
Log in
StoreQuote
ContactsContact us
  • Home Page
  • Explore IPU
  • Your Industry
    • Marine Industry
    • Oil & Gas Industry
    • Mining
    • Healthcare
    • Data Centres & IT Services
    • Power Generation
  • IPU Academy
  • Fuel Management Services
    • Case Studies
    • IPU Fuel Conditioning Programmes
    • Diesel Testing – DieselCheck Service & Kits
    • Fuel Polishing Systems – Diesel Defence
    • Diesel Defence Servicing
    • Cloud Based Fuel Monitoring
    • Diesel Defender Fuel Additive
    • Supporting Fuel Conditioning Products
    • What is Diesel Contamination?
    • Fuel Conditioning Contacts
  • Engine Starting
    • Case Studies
    • Hydraulic Engine Starting
    • Spring Starters – SureStart
    • Air Starters
    • Nitrogen Starting Systems
    • Reman Air Starter Motors
    • ATEX Starting
    • Inertia Starter Motors
    • Pre-engaged Starters
    • Servicing
    • Engine Starting Contacts
  • Case Studies
  • About IPU
    • About Us
    • Our capabilities
    • Our Distributors
    • IPU’s COVID-19 Response
    • Meet the Management Team
    • IPU Finance Options
    • Contact Us
    • Our History
    • Quality & Environmental
    • Modern Slavery Policy
    • Careers
    • News
    • Compliments & Complaints
  • Contact Us
  • Downloads
  • News

Home » News » Testing fuel before load bank testing could save you over £2,000

Testing fuel before load bank testing could save you over £2,000

April 20th, 2017 in Fuel Conditioning, News

Annual load bank testing is critical to ensure your gensets are ready should the mains power fail. Its key advantage is to highlight any issues affecting the engines reliability and capacity of your generator without the risk of losing critical systems. However, load bank testing is not cheap. If the generator fails then the test must be repeated. It’s therefore a good idea to remove any risks to your engines before you test your generators.

One obvious risk is contaminated fuel.

load bank testing
Regular load bank testing is critical to ensure the reliability of your gensets.
load bank testing
Dirty fuel can cause the load bank test to fail and result in the test being re-run.
load bank testing
Having your fuel tested before a load bank test is a lot less expensive than a re-test.

When a generator is exercised monthly it uses very little fuel. This could mask any fuel contamination symptoms. However, during load bank testing the engine has to work a lot harder and for longer. Your engine will use a lot more fuel and so the chances of contamination causing filters to block, injectors to suffer damage or complete engine failure are greatly increased. If the load bank test fails because of contaminated fuel then you’ll need to have your diesel tested and cleaned to cure the problem. You’ll then need to spend another £2,000 on a repeat load bank test.

A simple way to avoid this is to carry out a DieselCheck fuel test before you proceed with a load bank test. IPU’s DieselCheck Testing Service provides you with accurate, reliable fuel quality reports for each of your fuel tanks. We can even interpret the results for you and recommend a course of corrective actions (if needed). It’s a simple way to find out what’s in your fuel tank and is a lot less expensive than a load bank re-test.

Below are two scenarios:

Company A (no prior DieselCheck test) Company B (with a DieselCheck test)
1) Load bank testing fails 1) DieselCheck Fuel Test
2) DieselCheck Fuel Test 2) ClearTank Fuel Cleaning (if required)
3) ClearTank Fuel Cleaning 3) Load bank testing successful
4) 2nd load bank testing successful

Why are stand by generators affected by fuel contamination?

Standby generators by their very nature aren’t used very often. It’s their job to be there ‘just in case’. But this creates the perfect environment for fuel contamination to occur. If your generator is required to provide back up for a number of days, you will store tens of thousands of litres of diesel for months, years or even decades. We’ve created a short video below that explains why fuel contamination occurs:

 

« Previous Post
Next Post »
« Back to all News

Recent Blog Articles

  • OFTEC Inspections and How IPU Can Support November 30, 2022
  • IPU Exhibiting at Data Centres Ireland! November 15, 2022
  • IPU will be closed on Monday 19th Sept for Queen’s Funeral September 16, 2022
  • IPU Exhibiting at Electric & Power Indonesia! September 14, 2022
  • Vacancy: Trainee Sales and Proposals Engineer August 31, 2022

Get your free handbook

  • Fuel Housekeeping Handbook

    A free pocket guide with everything you can do to maintain your fuel.

Contacts

  • Ian Brewin
    Technical Proposals
    Office: +44 (0) 121 511 0400
    Mobile: +44 (0) 7436 837664
    Email: ian.brewin@ipu.co.uk

Downloads(no ID req'd)

  • IPU Fuel Conditioning Overview

Case Studies

  • Fuel Conditioning Programme protects Kent & Canterbury hospital
  • This field is for validation purposes and should be left unchanged.
IPU Group

Registered in England & Wales: 12167631

Industrial Power Units Ltd
Cygnus Way
West Bromwich
West Midlands
B70 0XB, UK

Contact us
+44 (0) 121 511 0400
+44 (0) 121 511 0401
ipu@ipu.co.uk
Links
  • Product Registration
  • Product Manuals
  • Terms & Conditions of Sales
  • Privacy & Cookies