Let's Talk
+44 (0) 121 511 0400
ipu@ipu.co.uk
IPU Group
Log in
StoreQuote
ContactsContact us
  • Home Page
  • Explore IPU
  • Your Industry
    • Marine Industry
    • Oil & Gas Industry
    • Mining
    • Healthcare
    • Data Centres & IT Services
    • Power Generation
  • IPU Academy
  • Fuel Management Services
    • Case Studies
    • IPU Fuel Conditioning Programmes
    • Diesel Testing – DieselCheck Service & Kits
    • Fuel Polishing Systems – Diesel Defence
    • Diesel Defence Servicing
    • Cloud Based Fuel Monitoring
    • Diesel Defender Fuel Additive
    • Supporting Fuel Conditioning Products
    • What is Diesel Contamination?
    • Fuel Conditioning Contacts
  • Engine Starting
    • Case Studies
    • Hydraulic Engine Starting
    • Spring Starters – SureStart
    • Air Starters
    • Nitrogen Starting Systems
    • Reman Air Starter Motors
    • ATEX Starting
    • Inertia Starter Motors
    • Pre-engaged Starters
    • Servicing
    • Engine Starting Contacts
  • Case Studies
  • About IPU
    • About Us
    • Our capabilities
    • Our Distributors
    • IPU’s COVID-19 Response
    • Meet the Management Team
    • IPU Finance Options
    • Contact Us
    • Our History
    • Quality & Environmental
    • Modern Slavery Policy
    • Careers
    • News
    • Compliments & Complaints
  • Contact Us
  • Downloads
  • News

Home » News » Engine Starting » NFPA 20 standard for air & hydraulic starting systems

NFPA 20 standard for air & hydraulic starting systems

February 14th, 2019 in Engine Starting, News

After a period of deliberation, the 2019 edition of the NFPA 20 standard has recently been released. There are notable additions to the regulations relating to the design of air and hydraulic starter motors. The preceding edition was published in 2016.

The NFPA 20 standard is an American set of guidelines determined by the National Fire Protection Association that rules on the installation of stationary pumps for fire protection.

Air and hydraulic starter motors are two of the staple ranges from IPU’s Engine Starting division, so this latest revision will be of interest to IPU and its customers.

For a simple overview of how the NFPA 20 standard affects the use of air & hydraulic starting systems,  order your free guide here.

Across both starter motor types, the main change has been the addition of a few rules on the use of primary and secondary cranking systems. They stipulate that engines fitted with multiple starting systems must use these definitions in order to differentiate between two separate cranking system types.

The following tables present the new regulations that have been included in the 2019 NFPA 20 standard, for both starter motor types. They relate largely to the cranking cycles for both the primary and secondary cranking systems.

 

Hydraulic Starting (Primary Cranking System)

2016 2019
Power source Unspecified Two equal-sized accumulators (11.2.7.3.11.1)
No. cranking cycles No fewer than 6

(11.2.7.3.5.6)

No fewer than 12

(11.2.7.3.11)

No. seconds per cycle No less than 15

(11.2.7.3.5.6)

No less than 15

(11.2.7.3.11)

Cranking method (cycles 1-6) 1-3 automatic from the signalling source; 4-6 not specified

(11.2.7.3.5.7)

Automatic from the signalling source, alternating between the accumulators

(11.2.7.3.11.2)

Cranking method (cycles 7-12) Unspecified Manually activated from engine or controller, with each button push initiating a 15-second crank

(11.2.7.3.11.3)

Automatic recharge system Electric powered

(11.2.7.3.5.2)

Electrically or air-powered

(11.2.7.3.6)

Engine-powered recharge Mandatory

(11.2.7.3.5.4)

Mandatory

(11.2.7.3.8)

Manual recharge Mandatory

(11.2.7.3.5.5)

Mandatory (recharge, purge & bleed)

(11.2.7.3.9)

Hydraulic Starting (Secondary Cranking System)

2016 2019
Power source Unspecified Unspecified
No. cranking cycles No fewer than 6

(11.2.7.3.5.6)

No fewer than 6

(11.2.7.3.12)

No. seconds per cycle No less than 15

(11.2.7.3.5.6)

No less than 15

(11.2.7.3.12)

Cranking method (cycles 1-3) Automatic from the signalling source

(11.2.7.3.5.7)

Automatic from the signalling source

(11.2.7.3.12.1)

Cranking method (cycles 4-6) Unspecified Manually activated from engine or controller, with each button push initiating a 15-second crank

(11.2.7.3.12.2)

Automatic recharge system Electric powered

(11.2.7.3.5.2)

Electrically or air-powered

(11.2.7.3.6)

Engine-powered recharge Mandatory

(11.2.7.3.5.4)

Mandatory

(11.2.7.3.8)

Manual recharge Mandatory

(11.2.7.3.5.5)

Mandatory (recharge, purge & bleed)

(11.2.7.3.9)

Air Starting (Primary Cranking System)

2016 2019
Power source Unspecified Two separate, equally-sized air supply containers (A and B)

(11.2.7.4.4.3)

Total cranking time 180 seconds

(11.2.7.4.4.1)

180 seconds

(11.2.7.4.4.2)

No. cranking cycles Unspecified 2
Duration of first cranking cycle Unspecified 90 seconds (continuous cranking)

(11.2.7.4.4.4)

Cranking method (first attempt) Unspecified Automatic from the signalling source, pulling from container A

(11.2.7.4.4.4)

Cranking method (second attempt) Unspecified Manually activated from engine or controller, pulling from container B and only cranking while the button is held in

(11.2.7.4.4.5)

Recharge system Independent of fire pump engine

(11.2.7.4.4.2)

Independent of fire pump engine

(11.2.7.4.4.9)

Air Starting (Secondary Cranking System)

2016 2019
Power source Unspecified Unspecified
Total cranking time 180 seconds

(11.2.7.4.4.1)

90 seconds

(11.2.7.4.4.6)

No. cranking cycles Unspecified 2
Duration of first cranking cycle Unspecified 45 seconds (continuous cranking)

(11.2.7.4.4.7)

Cranking method (first attempt) Unspecified Automatic from the signalling source

(11.2.7.4.4.7)

Cranking method (second attempt) Unspecified Manually activated from engine or controller, only cranking while the button is held in

(11.2.7.4.4.7)

Recharge system Independent of fire pump engine

(11.2.7.4.4.2)

Independent of fire pump engine

(11.2.7.4.4.9)

 

 

« Previous Post
Next Post »
« Back to all News

Recent Blog Articles

  • OFTEC Inspections and How IPU Can Support November 30, 2022
  • IPU Exhibiting at Data Centres Ireland! November 15, 2022
  • IPU will be closed on Monday 19th Sept for Queen’s Funeral September 16, 2022
  • IPU Exhibiting at Electric & Power Indonesia! September 14, 2022
  • Vacancy: Trainee Sales and Proposals Engineer August 31, 2022

Get your free handbook

  • IPU’s Quick Guide to NFPA 20

    Request this guide to understand the NFPA 20 guidelines that apply to engine starting systems.

Contacts

  • David Caddick
    Sales and Technical Director
    Office: +44 (0) 121 511 0400
    Mobile: +44 (0) 7831 582978
    Email: david.caddick@ipu.co.uk
  • Jon Cheetham
    Sales & Proposals Engineer
    Office: +33 2 54 72 63 00
    Mobile: +44 (0) 7825 944050
    Email: jon.cheetham@ipu.co.uk
  • Rob Toser
    Sales & Proposals Engineer
    Office: +44 (0) 121 511 0400
    Mobile: +44 (0) 7436 282685
    Email: rob.toser@ipu.co.uk

Downloads(no ID req'd)

  • IPU Engine Starting Systems Overview
  • This field is for validation purposes and should be left unchanged.
IPU Group

Registered in England & Wales: 12167631

Industrial Power Units Ltd
Cygnus Way
West Bromwich
West Midlands
B70 0XB, UK

Contact us
+44 (0) 121 511 0400
+44 (0) 121 511 0401
ipu@ipu.co.uk
Links
  • Product Registration
  • Product Manuals
  • Terms & Conditions of Sales
  • Privacy & Cookies